r07ds0983ej0100 rev.1.00 page 1 of 7 dec 20, 2012 preliminary datasheet bcr12lm-12ld 600v - 12a - triac medium power use features ? i t (rms) : 12 a ? v drm : 600 v ? i fgti , i rgti , i rgt ??? : 50 ma ? viso: 1800v ? insulated type ? planar passivation type ? tj: 150 c ? ul recognized: file no. e223904 outline renesas package code: prss0003af-a) ( package name: to-220fl) 1 2 3 2 1 3 1. t 1 terminal 2. t 2 terminal 3. gate terminal applications heater control, motor control maximum ratings voltage class parameter symbol 12 unit repetitive peak off-state voltage note1 v drm 600 v non-repetitive peak off-state voltage note1 v dsm 700 v parameter symbol ratings unit conditions rms on-state current i t (rms) 12 a commercial frequency, sine full wave 360? conduction, tc = 77 ?c surge on-state current i tsm 72 a 60 hz sinewave 1 full cycle, peak value, non-repetitive i 2 t for fusion i 2 t 21.6 a 2 s value corresponding to 1 cycle of half wave 60 hz, surge on-state current peak gate power dissipation p gm 5 w average gate power dissipation p g (av) 0.5 w peak gate voltage v gm 10 v peak gate current i gm 2 a junction temperature tj ?40 to +150 ?c storage temperature tstg ?40 to +150 ?c mass ? 1.5 g typical value isolation voltage note5 viso 1800 v ta = 25 ?c, ac 1 minute t 1 ? t 2 ? g terminal to case r07ds0983ej0100 rev.1.00 dec 20, 2012
bcr12lm-12ld preliminary r07ds0983ej0100 rev.1.00 page 2 of 7 dec 20, 2012 electrical characteristics rated value parameter symbol min. typ. max. unit test conditions repetitive peak off-state current i drm ? ? 2.0 ma tj = 150 ?c, v drm applied on-state voltage v tm ? ? 1.8 v tc = 25 ?c, i tm = 20a, instantaneous measurement ? v fgt ? ? ? 1.5 v ?? v rgt ? ? ? 1.5 v gate trigger voltage note2 ??? v rgt ??? ? ? 1.5 v tj = 25 ?c, v d = 6 v, r l = 6 ? , r g = 330 ? ? i fgt ? ? ? 50 ma ?? i rgt ? ? ? 50 ma gate trigger curent note2 ??? i rgt ??? ? ? 50 ma tj = 25 ?c, v d = 6 v, r l = 6 ? , r g = 330 ? gate non-trigger voltage v gd 0.2 ? ? v tj = 125 ?c, v d = 1/2 v drm thermal resistance r th (j-c) ? ? 4.3 ? c/w junction to case note3 critical-rate of rise of off-state commutation voltage note4 (dv/dt)c 10 ? ? v/ ? s tj = 125 ?c notes: 1. gate open. 2. measurement using the gate trigger characteristics measurement circuit. 3. the contact thermal resistance r th (c-f) in case of greasing is 0.5 ?c /w. 4. test conditions of the critical-rate of rise of off-state commutation voltage is shown in the table below. 5. make sure that your finished product containing this device meets your safe isolation requirements. for safety, it's advisable that heatsink is electrically floating. test conditions commutating voltage and current waveforms (inductive load) 1. junction temperature tj = 125 ?c 2. rate of decay of on-state commutating current (di/dt)c = ?6 a/ms 3. peak off-state voltage v d = 400 v supply voltage time time time main current main voltage (di/dt)c v d (dv/dt)c
bcr12lm-12ld preliminary r07ds0983ej0100 rev.1.00 page 3 of 7 dec 20, 2012 main characteristics 10 2 10 3 10 1 ?400 40 8 0 120 160 typical example 10 2 10 3 10 1 ?400 40 8 0 120 160 typical example 10 1 10 2 10 3 10 4 10 ?1 10 0 10 1 10 2 10 2 10 3 10 4 10 0 10 1 10 2 0 maximum on-state ch aracter istics on-state voltage (v) on-state current (a) rated surge on-state current conduction time (cycles at 60hz) surge on-state current (a) gate ch aracter istics (i, ii and iii) gate current (ma) gate voltage (v) gate trigger voltage vs. junct ion temperature junct ion temperature (c) gate trigger voltage (tj = tc) gate trigger voltage (tj = 25c) 100 (%) gate trigger current vs. junct ion temperature junct ion temperature (c) gate trigger current (tj = tc) gate trigger current (tj = 25c) 100 (%) maximum transient thermal impedance characteristics (junct ion to case) conduction time (cycles at 60hz) transient thermal i mpedance (c/w) 4 0123 10 2 10 1 10 0 10 ?1 10 2 10 1 10 0 10 ?1 tj = 25c 80 40 60 20 100 i rgt i i fgt i 5 4 3 2 1 0 v gd = 0.2 v v gt = 1.5 v p g(av) = 0.5 w v gm = 10 v p gm = 5 w i gm = 2 a i fgt i i rgt i i rgt iii i rgt iii
bcr12lm-12ld preliminary r07ds0983ej0100 rev.1.00 page 4 of 7 dec 20, 2012 12 8 4 0 16 20 0246 16 10 8 12 14 no fins 10 3 10 2 10 1 10 1 10 2 10 3 10 4 10 5 10 0 10 ?1 maximum transient thermal i mpedance character istics (junction to ambient) transient thermal impedance (c/w) conduction time (cycles at 60hz) on-state power dissipation (w) rms on-state current (a) maximum on-state power dissipation rms on-state current (a) case temperature (c) allowable case temperature vs. rms on-state current rms on-state current (a) allowable ambient temperature vs. rms on-state current ambient temperature (c) rms on-state current (a) ambient temperature (c) allowable ambient temperature vs. rms on-state current junction temperature (c) rep eti t ive peak o ff-state current ( tj = t c) rep eti t ive peak o ff-state current ( tj = 2 5c) 100 ( % ) repetitive peak off-state current vs. junction temperature 0 20 40 80 60 100 120 140 160 00 .5 1.01 .5 3. 02.5 2.0 n atu ral conv ecti on n o fin s cur v e s a pply regardl e ss o f condu cti on angl e resist ive , indu ctive loads 02468 10 12 1 6 14 0 20 40 80 60 100 120 140 160 02468 10 12 1 6 14 0 20 40 80 60 100 120 140 160 all fins are black painted aluminum and greased curves apply regardle ss of conduction angle 360 conduction resistive, inductive loads ?400 40 8 0120 160 10 6 10 5 10 4 10 3 10 2 typical example 360 conduction resistive, inductive loads cur v e s a pply regardl e ss o f condu cti on angl e resist ive , i ndu ctive load s n atu ral conv ecti on 60 0 t2.3 120 120 t2.3 100 100 t2.3
bcr12lm-12ld preliminary r07ds0983ej0100 rev.1.00 page 5 of 7 dec 20, 2012 ?00 40 8 01201 60 holding current vs. junction temperature junction temperature (c) holding current (tj = tc) holding current (tj = 25c) 100 (%) rate of rise of off-state voltage (v/) breakover voltage (dv/dt = xv/) breakover voltage (dv/dt = 1v/) 100 (%) b reakov er vo l tage vs. rate o f r ise o f o ff-state vo l tage ( tj = 125c) breakover voltage vs. junction temperature junction temperature (c) breakover voltage (tj = tc) breakover voltage (tj = 25c) 100 (%) typical example ?00 40 8 01201 60 0 20 40 80 60 100 120 140 160 typical example 0 20 40 80 60 100 120 140 160 typical example tj = 125c 10 1 10 2 10 3 10 4 10 3 10 2 10 1 latching current (ma) latching current vs. junction temperature junction temperature (c) 10 2 10 3 10 0 10 1 ?400 40 8 0120 160 distribution t 2 + , g ? typical example t 2 + , g + typical example t 2 ? , g ? typical example i quadrant iii quadrant rate of rise of off-state voltage (v/) breakover voltage (dv/dt = xv/) breakover voltage (dv/dt = 1v/) 100 (%) b reakov er vo l tage vs. rate o f r ise o f o ff-state vo l tage ( tj = 1 5 0 c) 0 20 40 80 60 100 120 140 160 typical example tj = 150c 10 1 10 2 10 3 10 4 i quadrant iii quadrant 10 1 10 0 10 2 10 2 10 1 10 0 commutation characteristics (tj=125c) critical rate of rise of off-state commutating v oltage (v/) minimum value m a i n v o l tage m a i n current i t (di/dt)c me time (dv/ dt)c typical example tj = 125c i t = 4a 00 200v f = 3 hz i quadrant iii quadrant rate of decay of on-state commutating current (a/ms)
bcr12lm-12ld preliminary r07ds0983ej0100 rev.1.00 page 6 of 7 dec 20, 2012 gate trigger characteristics test circuits test procedure i test procedure iii test procedure ii 6 330 330 330 a v a v a v iii quadrant 10 1 10 0 10 2 10 2 10 1 10 0 commutation characteristics (tj=150c) critical rate of rise of off-state commutating voltage (v/) rate of decay of on-state commutating current (a/ms) typical example tj = 1 5 0 c i t = 4a 00 200 v f = 3 hz i quadrant 10 3 10 2 10 1 10 1 10 0 10 2 gate trigger current (tw) gate trigger current (dc) 100 (%) gate current pulse width () gate trigger current vs. gate current pulse width typical example i rgt i i rgt iii i fgt i m a i n v o l tage m a i n current i t (di/dt)c me time (dv/dt)c
bcr12lm-12ld preliminary r07ds0983ej0100 rev.1.00 page 7 of 7 dec 20, 2012 package dimensions unit: mm previous code prss0003af-a to-220fl mass[typ.] 1.5g ? enesas code jeita package code package name to-220fl 3.6 0.3 15. 0 0.3 12.5 0.5 10.0 0.3 6.5 0.3 .2 0.2 0.75 0.15 1.15 0.2 2.54 0.25 2.54 0.25 2 .6 0 . 2 4.5 0.2 0.40 0.15 2.8 0.2 1.15 0.2 3.0 0.3 ordering information orderable part number packing quantity remark bcr12lm-12ld#b00 tube 50 pcs. straight type bcr12lm-12lda8#b00 tube 50 pcs. a8 lead form note: please confirm the specificati on about the shipping in detail.
notice 1. descriptions of circuits, software and other related information in this document are provided only to illustrate the operat ion of semiconductor products and application examples. you are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. renesas electronics has used reasonable care in preparing the information included in this document, but renesas electronics does not warrant that such information is error free. renesas electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. renesas electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property ri ghts of third parties by or arising from the use of renesas electronics products or technical information described in this document. no license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of renesas electronics or others. 4. you should not alter, modify, copy, or otherwise misappropriate any renesas electronics product, whether in whole or in part . renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of renesas electronics product. 5. renesas electronics products are classified according to the following two quality grades: "standard" and "high quality". t he recommended applications for each renesas electronics product depends on the product's quality grade, as indicated below. "standard": computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "high quality": transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. renesas electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). you must check the quality grade of each renesas electronics product before using it in a particular application. you may not use any renesas electronics product for any application for which it is not intended. renesas electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any renesas electronics product for which the product is not intended by renesas electronics. 6. you should use the renesas electronics products described in this document within the range specified by renesas electronics , especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. renesas electronics shall have no liability for malfunctions or damages arising out of the use of renesas electronics products beyond such specified ranges. 7. although renesas electronics endeavors to improve the quality and reliability of its products, semiconductor products have s pecific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. further, renesas electronics products are not subject to radiation resistance design. please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a renesas electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. please contact a renesas electronics sales office for details as to environmental matters such as the environmental compatib ility of each renesas electronics product. please use renesas electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the eu rohs directive. renesas electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. renesas electronics products and technology may not be used for or incorporated into any products or systems whose manufactu re, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. you should not use renesas electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. when exporting the renesas electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. it is the responsibility of the buyer or distributor of renesas electronics products, who distributes, disposes of, or othe rwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, renesas electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of renesas electronics products. 11. this document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of renesa s electronics. 12. please contact a renesas electronics sales office if you have any questions regarding the information contained in this doc ument or renesas electronics products, or if you have any other inquiries. (note 1) "renesas electronics" as used in this document means renesas electronics corporation and also includes its majority-o wned subsidiaries. (note 2) "renesas electronics product(s)" means any product developed or manufactured by or for renesas electronics. htt p ://www.renesas.co m refer to "htt p ://www.renesas.com/" for the latest and detailed information . r e n esas el ec tr o ni cs am e ri ca in c . 2880 scott boulevard santa clara , ca 95050-2554 , u.s.a . tel: +1-408-588-6000, fax: +1-408-588-6130 renesas electronics canada limited 1101 nicholson road, newmarket, ontario l3y 9c3, canada tel: +1-905-898-5441, fax: +1-905-898-3220 renesas electronics europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k tel: +44-1628-651-700, fax: +44-1628-651-804 renesas electronics europe gmbh arcadiastrasse 10, 40472 dsseldorf, germany tel: +49-211-65030, fax: +49-211-6503-1327 renesas electronics (china) co., ltd. 7th floor, quantum plaza, no.27 zhichunlu haidian district, beijing 100083, p.r.china tel: +86-10-8235-1155, fax: +86-10-8235-7679 renesas electronics (shanghai) co., ltd. unit 204, 205, azia center, no.1233 lujiazui ring rd., pudong district, shanghai 200120, china tel: +86-21-5877-1818, fax: +86-21-6887-7858 / -7898 renesas electronics hong kong limited unit 1601-1613, 16/f., tower 2, grand century place, 193 prince edward road west, mongkok, kowloon, hong kong tel: +852-2886-9318, fax: +852 2886-9022/9044 renesas electronics taiwan co., ltd. 13f, no. 363, fu shing north road, taipei, taiwan tel: +886-2-8175-9600, fax: +886 2-8175-9670 renesas electronics singapore pte. ltd. 80 bendemeer road, unit #06-02 hyflux innovation centre singapore 339949 tel: +65-6213-0200, fax: +65-6213-0300 renesas electronics mala y sia sdn.bhd. unit 906, block b, menara amcorp, amcorp trade centre, no. 18, jln persiaran barat, 46050 petalin g jaya, selan g or darul ehsan, malaysi a tel: +60-3-7955-9390 , fax: +60-3-7955-951 0 renesas electronics korea co. , ltd . 11f., samik lavied' or bld g ., 720-2 yeoksam-don g , kan g nam-ku, seoul 135-080, korea tel: +82-2-558-3737 , fax: +82-2-558-514 1 s ale s o ffi c e s ? 2012 renesas electronics corporation. all ri g hts reserved . colo p hon 2.2
|
